The BESS Exchange is sponsored by Edge On Up

Users browsing this forum: 7 Guest(s)

Mark this forum read \| Subscribe to this forum Edge Sharpness Testing
Thread / Author		Replies [asc]	Views	Rating	Last Post
	Effect of Chopping Board Material on Edge Longevity KnifeGrinders	7	23,206	0 Vote(s) - 0 out of 5 in Average	05-31-2019, 01:56 PM Last Post: grepper
	Just Couldn't Do It EOU	6	21,814	0 Vote(s) - 0 out of 5 in Average	11-17-2017, 06:11 PM Last Post: Bubby
	Scissors edge test SHARPCO	6	23,051	0 Vote(s) - 0 out of 5 in Average	04-26-2018, 01:31 PM Last Post: Mark Reich
	Tormek SG-250 results Sam Sloane	6	23,527	0 Vote(s) - 0 out of 5 in Average	01-23-2019, 10:51 PM Last Post: grepper
	3 finger test - I still don't get it grepper	5	18,692	0 Vote(s) - 0 out of 5 in Average	03-27-2017, 08:18 PM Last Post: Mark Reich
	Tale of a paring knife grepper	5	18,328	0 Vote(s) - 0 out of 5 in Average	05-31-2017, 09:21 PM Last Post: grepper
	Press fulcrum, then tester display 5g SHARPCO	5	19,826	0 Vote(s) - 0 out of 5 in Average	01-24-2018, 09:58 AM Last Post: EOU
	New high end cutlery edges? SHARPCO	5	19,899	0 Vote(s) - 0 out of 5 in Average	05-07-2018, 03:18 AM Last Post: Ken S
	Which knife sharpener is best? SHARPCO	5	17,729	0 Vote(s) - 0 out of 5 in Average	09-19-2020, 12:20 PM Last Post: Edgepal
	please assist with 150 BESS score hardheart	5	14,913	0 Vote(s) - 0 out of 5 in Average	10-17-2021, 02:25 PM Last Post: grepper
	Rocking Tester SHARPCO	4	17,447	0 Vote(s) - 0 out of 5 in Average	08-19-2018, 02:30 AM Last Post: SHARPCO
	Too sharp? grepper	4	14,382	0 Vote(s) - 0 out of 5 in Average	09-19-2020, 08:51 PM Last Post: grepper
	Rubber bottom cap for DCB10? Obsessive_newbie	4	12,923	0 Vote(s) - 0 out of 5 in Average	08-11-2022, 08:42 PM Last Post: Obsessive_newbie
	Bess to Grit Ratio Mark Reich	3	13,470	0 Vote(s) - 0 out of 5 in Average	07-23-2017, 10:26 AM Last Post: Mark Reich
	Edge retention by hardness, carbon content and wear-resistant alloys KnifeGrinders	3	19,580	1 Vote(s) - 5 out of 5 in Average	06-08-2018, 01:20 AM Last Post: KnifeGrinders
	TM02 vs DTC100 SHARPCO	3	12,173	0 Vote(s) - 0 out of 5 in Average	02-12-2020, 01:20 AM Last Post: SHARPCO
	0g Score Possible? 3D Anvil	3	10,483	0 Vote(s) - 0 out of 5 in Average	11-18-2022, 12:26 PM Last Post: 3D Anvil
	How to Create a Toothy Edge Without Really Trying grepper	2	11,214	0 Vote(s) - 0 out of 5 in Average	09-25-2017, 12:57 PM Last Post: grepper
	Disposable Test Clips Ken S	2	10,302	0 Vote(s) - 0 out of 5 in Average	08-24-2018, 06:58 PM Last Post: Ken S
	Trying out new PT50A Larrin	2	10,763	0 Vote(s) - 0 out of 5 in Average	09-13-2018, 05:12 PM Last Post: EOU

Pages (4): « Previous 1 2 3 4 Next »

New Posts

Hot Thread (New)

Hot Thread (No New)

No New Posts

Contains Posts by You

Locked Thread

Login
Username/Email:
Password:	Lost Password?
	Remember me