The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 871 - File: showthread.php PHP 7.4.33 (Linux)
File Line Function
/showthread.php 871 errorHandler->error



The BESS Exchange is sponsored by Edge On Up › BESS Forums › All About Edges v
First toothy edge

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Thread Modes
First toothy edge
SHARPCO Offline
Member
***
Posts: 219
Threads: 65
Joined: Jan 2018
#1
01-21-2019, 08:49 PM (This post was last modified: 01-21-2019, 09:23 PM by SHARPCO.)
   
I sharpen it with 240 grit belt. 

   
Then deburred with clean leather belt applied mineral oil only. I couldn't deburr completely. Is it LOW?

I got 200 BESS.
Find
Reply


Messages In This Thread
First toothy edge - by SHARPCO - 01-21-2019, 08:49 PM
RE: First toothy edge - by grepper - 01-21-2019, 10:19 PM
RE: First toothy edge - by SHARPCO - 01-21-2019, 10:58 PM
RE: First toothy edge - by grepper - 01-22-2019, 11:00 PM
RE: First toothy edge - by Ken S - 01-23-2019, 12:41 AM
RE: First toothy edge - by SHARPCO - 01-23-2019, 12:54 AM
RE: First toothy edge - by Mike Brubacher - 01-23-2019, 05:18 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 01:11 AM
RE: First toothy edge - by Mark Reich - 01-28-2019, 06:38 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:20 AM
RE: First toothy edge - by Mark Reich - 01-27-2019, 07:49 PM
RE: First toothy edge - by SHARPCO - 01-27-2019, 08:37 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:25 AM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:14 AM
RE: First toothy edge - by grepper - 01-28-2019, 07:47 PM
RE: First toothy edge - by SHARPCO - 01-29-2019, 12:36 AM
RE: First toothy edge - by Bud - 01-28-2019, 10:27 PM
RE: First toothy edge - by grepper - 01-28-2019, 10:50 PM
RE: First toothy edge - by Mark Reich - 01-28-2019, 11:21 PM
RE: First toothy edge - by Mike Brubacher - 01-29-2019, 12:17 PM
RE: First toothy edge - by Mark Reich - 01-29-2019, 03:17 PM
RE: First toothy edge - by grepper - 01-29-2019, 11:04 PM
RE: First toothy edge - by SHARPCO - 01-30-2019, 01:11 AM
RE: First toothy edge - by grepper - 01-30-2019, 11:09 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 01:23 AM
RE: First toothy edge - by grepper - 01-31-2019, 05:15 PM
RE: First toothy edge - by SHARPCO - 01-31-2019, 05:49 PM
RE: First toothy edge - by Mark Reich - 02-01-2019, 01:09 PM
RE: First toothy edge - by grepper - 02-01-2019, 05:03 PM
RE: First toothy edge - by SHARPCO - 02-01-2019, 08:22 PM
RE: First toothy edge - by Mark Reich - 02-02-2019, 08:25 PM
RE: First toothy edge - by SHARPCO - 02-02-2019, 10:10 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)